# This file allows user to override the factory # defaults for the WLAN Driver ############################################# # STA related general configurations ############################################# # Assigned MAC Addresses - This will be used until NV items are in place # Each byte of MAC address is represented in Hex format as XX Intf0MacAddress=000AF58989FF Intf1MacAddress=000AF58989FE Intf2MacAddress=000AF58989FD Intf3MacAddress=000AF58989FC #Channel Bonding gChannelBondingMode5GHz=1 gChannelBondingMode24GHz=0 #Enable Keep alive with non-zero period value gStaKeepAlivePeriod=60 # Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets) gVhtMpduLen=2 # 0 for OLPC 1 for CLPC and SCPC gEnableCloseLoop=1 ImplicitQosIsEnabled=0 # Enable Tx beamforming in VHT20MHz # Valid values are 0,1. If commented out, the default value is 0. # 0=disable, 1=enable gEnableTxBFin20MHz=1 #Enable/Disable SU Tx beamformer support. gEnableTxSUBeamformer=0 # 1=enable tx STBC; 0=disable gEnableTXSTBC=1 # 1=enable STBC; 0=disable STBC gEnableRXSTBC=1 # 1=enable rx LDPC; 0=disable gEnableRXLDPC=1 # Flag to allow STA send AddTspec even when ACM is Off gAddTSWhenACMIsOff=1 # RTS threshold RTSThreshold=1048576 # 802.11d support g11dSupportEnabled=0 # Phy Mode (auto, b, g, n, etc) # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only # 7 = 11b only 8 = 11ac only. gDot11Mode=0 # Enable Rx handling options # Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium) # Rx_thread + NAPI = 5 rx_mode=5 #Enable VHT on 2.4Ghz gEnableVhtFor24GHzBand=1 # Regulatory Setting; 0=STRICT; 1=CUSTOM gRegulatoryChangeCountry=1 # userspace country code setting shld take priority gCountryCodePriority=1 # Enable/Disable LPASS support # 0 to disable, 1 to enable gEnableLpassSupport=1 # Enable(1)/Disable(0) SIFS burst gEnableSifsBurst=1 # Tx Chain Mask for CCK gCckChainMaskEnable=1 # Tx Chain Mask for 1SS gTxChainMask1ss=0 # TPC power gSelfGenFrmPwr=3 gReportMaxLinkSpeed=0 enable_mac_provision=1 ################ NAN feature set start ################### # Enable or Disable NAN # 1=Enable (default), 0=Disable gEnableNanSupport=1 genable_nan_datapath=1 gnan_datapath_ndi_channel=6 ################ NAN feature set end ##################### gIgnorePeerHTopMode=1 gIgnorePeerErpInfo=1 # 802.11n Protection flag gEnableApProt=1 # Fixed Rate gFixedRate=0 # Intra-BSS forward gDisableIntraBssFwd=0 # WMM Enable/Disable WmmIsEnabled=0 # 802.11h support g11hSupportEnabled=1 #Short Guard Interval Enable/disable gShortGI20Mhz=1 gShortGI40Mhz=1 #Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec gWlanAutoShutdown=0 #Preferred band (both or 2.4 only or 5 only) BandCapability=0 gVhtChannelWidth=2 # Enable Tx beamforming gTxBFEnable=1 # Scan Timing Parameters # gPassiveMaxChannelTime=110 # gPassiveMinChannelTime=60 gActiveMaxChannelTime=40 gActiveMinChannelTime=20 #If set to 0, MCC is not allowed. gEnableMCCMode=1 # MCC to SCC Switch mode: # 0-Disable # 1-Enable # 2-Force SCC if same band, with SAP restart # 3-Force SCC if same band, without SAP restart by sending (E)CSA # 4-Force SCC if same band (or) use SAP mandatory channel for DBS, # without SAP restart by sending (E)CSA gWlanMccToSccSwitchMode = 3 # Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k) gVhtAmpduLenExponent=7 # Maximum number of concurrent connections gMaxConcurrentActiveSessions=3 # Radar PRI multiplier gDFSradarMappingPriMultiplier=4 # Enable or Disable Multi-user MIMO # 1=Enable (default), 0=Disable gEnableMuBformee=1 # Enable to check FW hash if secure FW feature is enabled. It's for defconfig # builds only since it will be ignored in performance/release builds. gEnableFWHashCheck=1 # Enable or Disable MCC Adaptive Scheduler at the FW # 1=Enable (default), 0=Disable gEnableMCCAdaptiveScheduler=1 # Disable/Enable GreenAP # 0 to disable, 1 to enable, default: 1 gEnableGreenAp=0 ################ Datapath feature set Begin ################ # Bus bandwidth threshold values in terms of number of packets gBusBandwidthHighThreshold=2000 gBusBandwidthMediumThreshold=500 gBusBandwidthLowThreshold=150 # Bus bandwidth compute timeout value in ms gBusBandwidthComputeInterval=100 # VHT Tx/Rx MCS values # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gVhtRxMCS=2 gVhtTxMCS=2 # VHT Tx/Rx MCS values for 2x2 # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gEnable2x2=1 gVhtRxMCS2x2=2 gVhtTxMCS2x2=2 # Enable/Disable RX full reorder offload gReorderOffloadSupported=1 # Enable CE classification # 1 - enable(default) 0 - disable gCEClassifyEnable=1 # Enable(Tx) fastpath for data traffic. # 1 - enable(default) 0 - disable gEnableFastPath=1 # This flag enables IP, TCP and UDP checksum offload # 1 - enable(default) 0 - disable gEnableIpTcpUdpChecksumOffload=1 # Enable TCP Segmentation Offload # 1 - enable 0 - disable TSOEnable=1 # Enable Generic Receive Offload # LRO and GRO are exclusive to each other # LRO support is deprecated on latest 4.9(SDM845) kernel GROEnable=1 # Enable HT MPDU Density # 4 for 2 micro sec ght_mpdu_density=4 # Enable flow steering to enable multiple CEs for Rx flows. # Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs. # Parallel Rx paths. # 1 - enable 0 - disable(default) gEnableFlowSteering=1 ce_service_max_yield_time=500 ce_service_max_rx_ind_flush=1 maxMSDUsPerRxInd=8 gEnableDataStallDetection=0 gTcpLimitOutputEnable=0 ################ Datapath feature set End ################ ############################################# # SCAN related configurations ############################################# # Enable/Disable Idle Scan gEnableIdleScan=0 #Enable Scan Results Aging based on timer #Timer value is in seconds #If Set to 0 it will not enable the feature gScanAgingTime=30 #Enable Scan Results Aging based on number of scans gScanResultAgeCount=1 #Enable thermal mitigation gThermalMitigationEnable=0 #Maximum Channel time in msec gMaxMediumTime=6000 gPNOScanSupport=1 # Enable or Disable Extended Scan (GScan) # 1=Enable (default), 0=Disable gExtScanEnable=1 #If set will start with active scan after driver load, otherwise will start with #passive scan to find out the domain gEnableBypass11d=1 #If set to 0, will not scan DFS channels gEnableDFSChnlScan=1 #Maxium Channel time in msec gMaxMediumTime = 6000 adaptive_dwell_mode_enabled=1 hostscan_adaptive_dwell_mode=1 adapt_dwell_lpf_weight=80 adapt_dwell_wifi_act_threshold=10 # Enable or disable Probe Req Information Element whitelist. When enabled, IEs corresponding to bits # set in bitmaps are allowed in probe request, all others removed while device is unassociated # with an AP # 1=Enable, 0=Disable (default) g_enable_probereq_whitelist_ies=1 # ie bitmap examples: = [] # g_probe_req_ie_bitmap_0=0x80000009 #[0, 3, 31] # g_probe_req_ie_bitmap_0=0x00000000 #[] (default) # g_probe_req_ie_bitmap_1=0x80000009 #[32, 35, 63] g_probe_req_ie_bitmap_0=0x0000000B g_probe_req_ie_bitmap_1=0x00040000 # g_probe_req_ie_bitmap_2=0x00000000 # g_probe_req_ie_bitmap_3=0x00000000 # g_probe_req_ie_bitmap_4=0x00000000 # g_probe_req_ie_bitmap_5=0x00000000 g_probe_req_ie_bitmap_6=0x20000000 # g_probe_req_ie_bitmap_7=0x00000000 gProbeReqOUIs=0050F208 ############################################# # Power related configurations ############################################# # Enable IMPS or not gEnableImps=1 # Enable BMPS or not gEnableBmps=1 # Increase sleep duration (seconds) during IMPS # 0 implies no periodic wake up from IMPS. Periodic wakeup is # unnecessary if Idle Scan is disabled. gImpsModSleepTime=0 # UAPSD service interval for VO,VI, BE, BK traffic InfraUapsdVoSrvIntv=0 InfraUapsdViSrvIntv=0 InfraUapsdBeSrvIntv=0 InfraUapsdBkSrvIntv=0 # Enable suspend or not # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter gEnableSuspend=3 #Enable Power Save offload gEnablePowerSaveOffload=2 #Enable Power saving mechanism Based on Android Framework #If set to 0 Driver internally control the Power saving mechanism #If set to 1 Android Framwrok control the Power saving mechanism isAndroidPsEn=0 beaconEarlyTerminationWakeInterval=3 #Data Inactivity Timeout when in powersave (in ms) gDataInactivityTimeout=200 # Inactivity time (in ms) to end TX Service Period while in IBSS power save mode gIbssTxSpEndInactivityTime=10 gEnableModulatedDTIM=2 gMaxLIModulatedDTIM=6 ############################################# # Roaming related configurations ############################################# # CSR Roaming Enable(1) Disable(0) gRoamingTime=0 # ESE Support and fast transition EseEnabled=1 gNeighborLookupThreshold=76 gNeighborReassocThreshold=81 gNeighborScanChannelMinTime=20 gNeighborScanChannelMaxTime=30 gMaxNeighborReqTries=3 # To enable, set gRoamIntraBand=1 (Roaming within band) # To disable, set gRoamIntraBand=0 (Roaming across band) gRoamIntraBand=0 # Legacy (non-ESE, non-802.11r) Fast Roaming Support # To enable, set FastRoamEnabled=1 # To disable, set FastRoamEnabled=0 FastRoamEnabled=1 #Check if the AP to which we are roaming is better than current AP in terms of RSSI. #Checking is disabled if set to Zero.Otherwise it will use this value as to how better #the RSSI of the new/roamable AP should be for roaming RoamRssiDiff=3 # If the RSSI of any available candidate is better than currently associated # AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without # registering for reassoc threshold). # NOTE: Value of 0 means that we would register for reassoc threshold. gImmediateRoamRssiDiff=10 # 802.11K support gRrmEnable=1 gRrmOperChanMax=8 gRrmNonOperChanMax=8 gEnableFastRoamInConcurrency=1 # Enable/Disable Roaming Offload Support (a.k.a Key Management Offload) # 0 to disable, 1 to enable gRoamOffloadEnabled=1 gAllowDFSChannelRoam=1 gLFRSubnetDetectionEnable=0 ############################################# # Offload related configurations ############################################# # Beacon filtering frequency (unit in beacon intervals) gNthBeaconFilter=50 # Enable WAPI or not # WAPIIsEnabled=0 #Flag to enable HostARPOffload feature or not hostArpOffload=1 #Flag to enable HostNSOffload feature or not hostNSOffload=1 # controlling the following offload patterns # through ini parameter. Default value is 1 # to disable set it to zero. ssdp = 0 # Setup multicast pattern for mDNS 224.0.0.251, # SSDP 239.255.255.250 and LLMNR 224.0.0.252 ssdp = 0 #Enable MC address filtering offload gMCAddrListEnable=1 #Enable Active mode offload gActiveModeOffload=1 #Enable Active mode offload gEnableActiveModeOffload=1 #Enable APF in Active mode gActiveUcBpfMode=2 gActiveMcBcBpfMode=1 #HW CCE Filter mode gHwFilterMode=0 # WOW Enable/Disable. # 0 - Disable both magic pattern match and pattern byte match. # 1 - Enable magic pattern match on all interfaces. # 2 - Enable pattern byte match on all interfaces. # 3 - Enable both magic patter and pattern byte match on all interfaces. # Default value of gEnableWoW is 3. # gEnableWoW=0 11k_offload_enable_bitmask=0 ############################################# # Logging related configurations ############################################# gEnableLogp=1 gEnableSelfRecovery=1 #Enable firmware log gEnablefwlog=1 # Additional firmware log levels gFwDebugLogLevel=3 gFwDebugModuleLoglevel=2,1,3,1,5,1,9,1,13,1,14,1,18,1,19,1,26,1,28,1,29,1,31,1,36,1,38,1,46,1,47,1,50,1,52,1,53,1,56,1,60,1,61,1,4,1 #Enable firmware uart print gEnablefwprint=0 ############################################# # TDLS related configurations ############################################# # Enable support for TDLS # 0 - disable # 1 - enable gEnableTDLSSupport=1 # Enable support for Implicit Trigger of TDLS. That is, wlan driver shall # initiate TDLS Discovery towards a peer whenever setup criteria (throughput # and RSSI) is met and then will initiate teardown when teardown criteria # (idle packet count and RSSI) is met. # 0 - disable # 1 - enable gEnableTDLSImplicitTrigger=1 # Enable TDLS External Control. That is, user space application has to # first configure a peer MAC in wlan driver towards which TDLS is desired. # Device will establish TDLS only towards those configured peers whenever # TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS # when teardown criteria (idle packet count and RSSI) is met. However, # device will accept TDLS connection if it is initiated from any other peer, # even if that peer is not configured. # 0 - disable # 1 - enable # For TDLS External Control, Implicit Trigger must also be enabled. gTDLSExternalControl=1 # Enable support for TDLS off-channel operation # 0 - disable # 1 - enable # TDLS off-channel operation will be invoked when there is only one # TDLS connection. gEnableTDLSOffChannel=0 gEnableTDLSScan=1 gTDLSTxPacketThreshold=10 gTDLSIdlePacketThreshold=1 ############################################# # P2P related configurations ############################################# #P2P Listen offload gEnableP2pListenOffload=1 #Enable or Disable p2p device address administered isP2pDeviceAddrAdministrated=0 #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). #For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) #For both active and power save clients. #Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. #If doesn't honor for 5 seconds then DUT remove client. # chain mask related params # # Set txchainmask and rxchainmask # These parameters are used only if gEnable2x2 is 0 # Valid values are 1,2 # Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. # Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. gSetTxChainmask1x1=1 gSetRxChainmask1x1=1 # Following parameters are for test purpose only and when set will # configure tx and rx per band chain mask. These parameters will # take effect only when: # gEnable2x2=0 # gDualMacFeatureDisable=1 # gSetTxChainmask1x1=0 # gSetRxChainmask1x1=0 # These are defaulted to 0 with following definitions: # 0: don't care # 1: use chain 0 # 2: use chain 1 # 3: can use either chain tx_chain_mask_2g=0 rx_chain_mask_2g=0 tx_chain_mask_5g=0 rx_chain_mask_5g=0 gForce1x1Exception=0 #IPA config is a bit mask and following are the configurations. #bit0 IPA Enable #bit1 IPA PRE Filter enable #bit2 IPv6 enable #bit3 IPA Resource Manager (RM) enable #bit4 IPA Clock scaling enable #bit5 IPA uC ENABLE #bit6 IPA uC STA ENABLE #bit7 IPA Real Time Debugging gIPAConfig=0x7d gIPADescSize=800 #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period #where we send NULL frame. #gApLinkMonitorPeriod = 10 #gGoLinkMonitorPeriod = 10 #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. #Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. gGoKeepAlivePeriod = 20 gApKeepAlivePeriod = 20 ############################################# # SAP related configurations ############################################# #Enable OBSS protection gEnableApOBSSProt=1 #Enable/Disable UAPSD for SoftAP gEnableApUapsd=1 # SAP auto channel selection configuration # 0 = disable auto channel selection # 1 = enable auto channel selection, channel provided by supplicant will be ignored gApAutoChannelSelection=0 #SOFTAP Channel Range selection gAPChannelSelectStartChannel=1 gAPChannelSelectEndChannel=11 # SAP Country code # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. # Example # US Indoor, USI # Korea Outdoor, KRO # Japan without optional byte, JP # France without optional byte, FR #gAPCntryCode=USI # DFS Master Capability gEnableDFSMasterCap=0 #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled gAPAutoShutOff=0 # Remove Overlap channel restriction gEnableOverLapCh=0 # Enable/Disable channel avoidance for SAP in SCC scenario # 0 - disable # 1 - enable gSapSccChanAvoidance=0 #Enable/Disable Tx beamformee in SAP mode gEnableTxBFeeSAP=1 #Enable/Disable dual MAC feature # 0 - enable DBS # 1 - disable DBS # 2 - disable DBS for connection but keep DBS for scan # 3 - disable DBS for connection but keep DBS scan with async # scan policy disabled # 4 - enable DBS for connection as well as for scan with async # scan policy disabled # 5 - enable DBS for connection but disable dbs for scan. # 6 - enable DBS for connection but disable simultaneous scan from # upper layer (DBS scan remains enabled in FW). gDualMacFeatureDisable=6 # Turn on STA + AP/STA gEnableConcurrentSTA=wlan1 # 0 - Disallow STA+SAP SCC on LTE coex channel # 1 - Allow STA+SAP SCC on LTE coex channel g_sta_sap_scc_on_lte_coex_chan=1 #Set priority for connection with bssid_hint g_is_bssid_hint_priority=0 gdbs_scan_selection=5,4,1,16,4,1 enable_11d_in_world_mode=1 gDptraceConfig=1,4,1,126 ############################################# # MAWC related configurations ############################################# # MAWCEnabled - Enable/Disable Motion Aided Wireless Connectivity Global MAWCEnabled=0 # mawc_roam_enabled - Enable/Disable MAWC during roaming mawc_roam_enabled=0 # Enable/Disable the Motion Aided Wireless Connectivity # based NLO using this parameter mawc_nlo_enabled=0 #Enable/Disable chain selection optimization for one chain dtim #Min: 0 #MAX: 30 gEnableDTIMSelectionDiversity=3 # Enable/Disable rtt sta mac randomization enable_rtt_mac_randomization=1 gAP11ACOverride=0 channel_select_logic_conc=0x0 gConfigVCmode=0 wlm_latency_flags_moderate=0 wlm_latency_flags_low=0 wlm_latency_flags_ultralow=0 oce_sta_enable=0 oce_sap_enable=0 num_oce_wan_slots=0 oce_wan_score_idx7_to_4=0 oce_wan_score_idx11_to_8=0 oce_enable_rssi_assoc_reject=0 # Enable/Disable rtt sta mac randomization enable_rtt_mac_randomization=1 #Enable/Disable Secondary Retry Rate feature subset gEnableSecondaryRate=0x17 #Timer waiting for interface up from the upper layer gInterfaceChangeWait=1000 #Enable Bmps(power save in connected state) based on timer #Timer value is in seconds gAutoBmpsTimerValue=90 #Enable/Disable 802.11ai FILS support g_is_fils_enabled=0 END # Note: Configuration parser would not read anything past the END marker