You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
520 lines
15 KiB
520 lines
15 KiB
# This file allows user to override the factory
|
|
# defaults for the WLAN Driver
|
|
|
|
#############################################
|
|
# Power related configurations
|
|
#############################################
|
|
# Phy Mode (auto, b, g, n, etc)
|
|
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
|
|
# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
|
|
# 7 = 11b only 8 = 11ac only.
|
|
gDot11Mode=0
|
|
|
|
#############################################
|
|
# STA related general configurations
|
|
#############################################
|
|
# UAPSD service interval for VO,VI, BE, BK traffic
|
|
InfraUapsdVoSrvIntv=0
|
|
InfraUapsdViSrvIntv=0
|
|
InfraUapsdBeSrvIntv=0
|
|
InfraUapsdBkSrvIntv=0
|
|
|
|
# Flag to allow STA send AddTspec even when ACM is Off
|
|
gAddTSWhenACMIsOff=1
|
|
|
|
#############################################
|
|
# SAP related configurations
|
|
#############################################
|
|
#Enable OBSS protection
|
|
gEnableApOBSSProt=1
|
|
|
|
# RTS threshold
|
|
RTSThreshold=1048576
|
|
|
|
# 802.11d support
|
|
g11dSupportEnabled=0
|
|
|
|
# DFS Master Capability
|
|
gEnableDFSMasterCap=0
|
|
|
|
gNeighborLookupThreshold=76
|
|
|
|
# Legacy (non-ESE, non-802.11r) Fast Roaming Support
|
|
# To enable, set FastRoamEnabled=1
|
|
# To disable, set FastRoamEnabled=0
|
|
FastRoamEnabled=1
|
|
|
|
# Check if the AP to which we are roaming is better than current AP in
|
|
# terms of RSSI. Checking is disabled if set to Zero.Otherwise it will
|
|
# use this value as to how better the RSSI of the new/roamable AP should
|
|
# be for roaming
|
|
RoamRssiDiff=3
|
|
|
|
#Channel Bonding
|
|
gChannelBondingMode24GHz=0
|
|
gChannelBondingMode5GHz=1
|
|
|
|
# Enable DFS channel roam
|
|
# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
|
|
gAllowDFSChannelRoam=1
|
|
|
|
# chain mask related params
|
|
#
|
|
# Set txchainmask and rxchainmask
|
|
# These parameters are used only if gEnable2x2 is 0
|
|
# Valid values are 1,2
|
|
# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
|
|
# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
|
|
gSetTxChainmask1x1=1
|
|
gSetRxChainmask1x1=1
|
|
|
|
# MCC to SCC Switch mode:
|
|
# 0-Disable
|
|
# 1-Enable
|
|
# 2-Force SCC if same band, with SAP restart
|
|
# 3-Force SCC if same band, without SAP restart by sending (E)CSA
|
|
# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
|
|
# without SAP restart by sending (E)CSA
|
|
gWlanMccToSccSwitchMode = 3
|
|
|
|
#Allow STA+SAP SCC on DFS channel with master mode support disabled.
|
|
g_sta_sap_scc_on_dfs_chan = 0
|
|
|
|
# 1=enable tx STBC; 0=disable
|
|
gEnableTXSTBC=1
|
|
|
|
# 1=enable rx LDPC; 0=disable
|
|
gEnableRXLDPC=1
|
|
|
|
#Enable/Disable Tx beamformee in SAP mode
|
|
gEnableTxBFeeSAP=1
|
|
|
|
# Enable Tx beamforming in VHT20MHz
|
|
# Valid values are 0,1. If commented out, the default value is 0.
|
|
# 0=disable, 1=enable
|
|
gEnableTxBFin20MHz=1
|
|
|
|
# 802.11K support
|
|
gRrmEnable=1
|
|
|
|
#Enable Power Save offload
|
|
gEnablePowerSaveOffload=2
|
|
|
|
# Maximum Receive AMPDU size (VHT only. Valid values:
|
|
# 0->8k 1->16k 2->32k 3->64k 4->128k)
|
|
gVhtAmpduLenExponent=7
|
|
|
|
# Maximum MPDU length (VHT only. Valid values:
|
|
# 0->3895 octets, 1->7991 octets, 2->11454 octets)
|
|
gVhtMpduLen=2
|
|
|
|
# Report actual link speed (not max or scaled)
|
|
gReportMaxLinkSpeed=0
|
|
|
|
#############################################
|
|
# P2P related configurations
|
|
#############################################
|
|
#Enable or Disable p2p device address administered
|
|
isP2pDeviceAddrAdministrated=0
|
|
|
|
#Mac address provisioning
|
|
enable_mac_provision=1
|
|
|
|
#Enable VHT on 2.4Ghz
|
|
gEnableVhtFor24GHzBand=1
|
|
|
|
#############################################
|
|
# Offload related configurations
|
|
#############################################
|
|
|
|
# controlling the following offload patterns
|
|
# through ini parameter. Default value is 1
|
|
# to disable set it to zero. ssdp = 0
|
|
# Setup multicast pattern for mDNS 224.0.0.251,
|
|
# SSDP 239.255.255.250 and LLMNR 224.0.0.252
|
|
ssdp=0
|
|
|
|
# Regulatory Setting; 0=STRICT; 1=CUSTOM
|
|
gRegulatoryChangeCountry=1
|
|
|
|
# Disable/Enable GreenAP
|
|
# 0 to disable, 1 to enable, default: 1
|
|
gEnableGreenAp=0
|
|
|
|
#Enable/Disable LPASS support
|
|
# 0 to disable, 1 to enable
|
|
gEnableLpassSupport=1
|
|
|
|
# Whether userspace country code setting shld have priority
|
|
gCountryCodePriority=1
|
|
|
|
# Enable or Disable Multi-user MIMO
|
|
# 1=Enable (default), 0=Disable
|
|
gEnableMuBformee=1
|
|
|
|
# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
|
|
gIbssTxSpEndInactivityTime=10
|
|
|
|
#############################################
|
|
# TDLS related configurations
|
|
#############################################
|
|
# Enable support for TDLS
|
|
# 0 - disable
|
|
# 1 - enable
|
|
gEnableTDLSSupport=1
|
|
|
|
# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
|
|
# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
|
|
# and RSSI) is met and then will initiate teardown when teardown criteria
|
|
# (idle packet count and RSSI) is met.
|
|
# 0 - disable
|
|
# 1 - enable
|
|
gEnableTDLSImplicitTrigger=1
|
|
|
|
# Enable support for TDLS off-channel operation
|
|
# 0 - disable
|
|
# 1 - enable
|
|
# TDLS off-channel operation will be invoked when there is only one
|
|
# TDLS connection.
|
|
gEnableTDLSOffChannel=0
|
|
|
|
# Tx/Rx Packet threshold for initiating TDLS.
|
|
# This ini is used to configure the number of Tx/Rx packets during the period of
|
|
# gTDLSTxStatsPeriod when exceeded, a TDLS Discovery request is triggered.
|
|
gTDLSTxPacketThreshold=10
|
|
|
|
# Number of idle packet.
|
|
# This ini is used to configure the number of Tx/Rx packet, below which
|
|
# within last gTDLSTxStatsPeriod period is considered as idle condition.
|
|
gTDLSIdlePacketThreshold=1
|
|
|
|
# VHT Tx/Rx MCS values
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
|
gVhtRxMCS=2
|
|
gVhtTxMCS=2
|
|
|
|
# VHT Tx/Rx MCS values for 2x2
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
|
gEnable2x2=1
|
|
gVhtRxMCS2x2=2
|
|
gVhtTxMCS2x2=2
|
|
|
|
#IPA config is a bit mask and following are the configurations.
|
|
#bit0 IPA Enable
|
|
#bit1 IPA PRE Filter enable
|
|
#bit2 IPv6 enable
|
|
#bit3 IPA Resource Manager (RM) enable
|
|
#bit4 IPA Clock scaling enable
|
|
#bit5 IPA uC ENABLE
|
|
#bit6 IPA uC STA ENABLE
|
|
#bit8 IPA Real Time Debugging
|
|
gIPAConfig=0x7d
|
|
|
|
# Enable Rx handling options
|
|
# Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium)
|
|
# Rx_thread + NAPI = 5
|
|
rx_mode=5
|
|
|
|
# Enable(Tx) fastpath for data traffic.
|
|
# 1 - enable(default) 0 - disable
|
|
gEnableFastPath=1
|
|
|
|
# Enable TCP Segmentation Offload
|
|
# 1 - enable 0 - disable
|
|
TSOEnable=1
|
|
|
|
# Enable Generic Receive Offload
|
|
# LRO and GRO are exclusive to each other
|
|
# LRO support is deprecated on latest 4.9(SDM845) kernel
|
|
# 1 - enable(default) 0 - disable
|
|
GROEnable=1
|
|
|
|
# Enable HT MPDU Density
|
|
# 4 for 2 micro sec
|
|
ght_mpdu_density=4
|
|
|
|
# Enable flow steering to enable multiple CEs for Rx flows.
|
|
# Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
|
|
# Parallel Rx paths.
|
|
# 1 - enable 0 - disable(default)
|
|
gEnableFlowSteering=1
|
|
|
|
# Time in microseconds after which a NAPI poll must yield
|
|
ce_service_max_yield_time=500
|
|
|
|
#Maximum number of HTT messages to be processed per NAPI poll
|
|
ce_service_max_rx_ind_flush=1
|
|
|
|
# Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND
|
|
maxMSDUsPerRxInd=8
|
|
################ Datapath feature set End ################
|
|
|
|
################ NAN feature set start ###################
|
|
|
|
# Enable NAN discovery (NAN 1.0)
|
|
# 1 - enable 0 - disable(default)
|
|
gEnableNanSupport=1
|
|
################ NAN feature set end #####################
|
|
|
|
hostscan_adaptive_dwell_mode=1
|
|
|
|
# Create another interface during driver load
|
|
gEnableConcurrentSTA=wlan1
|
|
|
|
#Enable/Disable dual MAC feature
|
|
# 0 - enable DBS
|
|
# 1 - disable DBS
|
|
# 2 - disable DBS for connection but keep DBS for scan
|
|
# 3 - disable DBS for connection but keep DBS scan with async
|
|
# scan policy disabled
|
|
# 4 - enable DBS for connection as well as for scan with async
|
|
# scan policy disabled
|
|
# 5 - enable DBS for connection but disable dbs for scan.
|
|
# 6 - enable DBS for connection but disable simultaneous scan from
|
|
# upper layer (DBS scan remains enabled in FW).
|
|
gDualMacFeatureDisable=6
|
|
|
|
#Enable/Disable latency mode
|
|
# 0 disable
|
|
# 1 enable
|
|
wlm_latency_enable=1
|
|
|
|
# Enable/Disable NUD Tracking within driver
|
|
gEnableNUDTracking=0
|
|
|
|
# Configure hardware filter for DTIM mode
|
|
# The hardware filter is only effective in DTIM mode.
|
|
# Use this configuration to blanket drop broadcast/multicast packets at the hardware level
|
|
# without waking up the firmware
|
|
#
|
|
# Takes a bitmap of frame types to drop
|
|
#
|
|
# 0 = disable feature
|
|
# 1 = drop all broadcast frames, except ARP (default)
|
|
# 2 = drop all multicast frames, except ICMPv6
|
|
# 3 = drop all broadcast and multicast frames, except ARP and ICMPv6
|
|
gHwFilterMode=0
|
|
|
|
# Enables SNR Monitoring
|
|
# This ini is used to set default snr monitor
|
|
gEnableSNRMonitoring=1
|
|
|
|
# Control to enable TCP limit output byte
|
|
# This ini is used to enable dynamic configuration of TCP limit output bytes
|
|
# tcp_limit_output_bytes param.
|
|
# Enabling this will let driver post message to cnss-daemon,
|
|
# accordingly cnss-daemon will modify the tcp_limit_output_bytes.
|
|
gTcpLimitOutputEnable=0
|
|
|
|
# Enable Target Wake Time support.
|
|
# This ini is used to enable or disable TWT support.
|
|
enable_twt=0
|
|
|
|
# For NLO/PNO, enable MAWC based scan
|
|
# Enable/Disable the Motion Aided Wireless Connectivity based NLO using this parameter
|
|
mawc_nlo_enabled=0
|
|
|
|
# Force 1x1 when connecting to certain peer
|
|
# This INI when enabled will force 1x1 connection with certain peer.
|
|
gForce1x1Exception=0
|
|
|
|
# Enable/disable oce feature for STA
|
|
# This ini is used to enable/disable oce feature for STA
|
|
oce_sta_enable=1
|
|
|
|
# Enable/disable oce feature for SAP
|
|
# This ini is used to enable/disable oce feature for SAP
|
|
oce_sap_enable=0
|
|
|
|
#Enable/disable FILS discovery for SAP
|
|
oce_enable_fils_discovery_sap=0
|
|
|
|
# Set probe request rate
|
|
# This ini is used to set probe request rate to 5.5Mbps as per OCE requirement in 2.4G band
|
|
oce_enable_probe_req_rate=0
|
|
|
|
#Enable/disable probe request deferral as per OCE spec
|
|
oce_enable_probe_req_deferral=0
|
|
|
|
# HE caps Weightage to calculate best candidate
|
|
# This ini is used to increase/decrease HE caps weightage in best candidate selection.
|
|
# If AP supports HE caps, AP will get additional weightage with this param.
|
|
# Weightage will be given only if dot11mode is HE capable.
|
|
he_caps_weightage=0
|
|
|
|
# PCL Weightage to calculate best candidate
|
|
# This ini is used to increase/decrease PCL weightage in best candidate selection.
|
|
# If some APs are in PCL list, those AP will get addition weightage.
|
|
pcl_weightage=10
|
|
|
|
# Enable/disable esp feature
|
|
# This ini is used to enable/disable ESP(Estimated service parameters) IE parsing and decides
|
|
# whether firmware will include this in its scoring algo.
|
|
enable_esp_for_roam=0
|
|
|
|
# Bitmask to enable 11k offload to FW.
|
|
# This ini is used to set which of the 11k features is offloaded to FW
|
|
# Currently Neighbor Report Request is supported for offload and is enabled by default.
|
|
# B0: Offload 11k neighbor report requests
|
|
# B1-B31: Reserved
|
|
11k_offload_enable_bitmask=0
|
|
|
|
# Set channel selection logic for different concurrency combinations to DBS or inter band MCC.
|
|
# Default is DBS for STA+STA and STA+P2P.
|
|
# 0 - inter-band MCC
|
|
# 1 - DBS
|
|
#
|
|
# BIT 0: STA+STA
|
|
# BIT 1: STA+P2P
|
|
# BIT 2-31: Reserved
|
|
channel_select_logic_conc=0
|
|
|
|
# Configure BTM
|
|
# Bit 0: Enable/Disable the BTM offload. Set this to 1 will enable and 0 will disable BTM offload.
|
|
# BIT 2, 1: Action on non matching candidate with cache. If a BTM request is received from AP
|
|
# then the candidate AP's may/may-not be present in the firmware scan cache.
|
|
# Based on below config firmware will decide whether to forward BTM frame to host or
|
|
# consume with firmware and proceed with Roaming to candidate AP.
|
|
#
|
|
# 00 scan and consume
|
|
# 01 no scan and forward to host
|
|
# 10, 11 reserved
|
|
# BIT 5, 4, 3: Roaming handoff decisions on multiple candidates match
|
|
# 000 match if exact BSSIDs are found
|
|
# 001 match if at least one top priority BSSID only
|
|
# 010, 011, 100, 101, 110, 111 reserved
|
|
# BIT 6: Set this to 1 will send BTM query frame and 0 not sent.
|
|
# BIT 7-31: Reserved
|
|
btm_offload_config=1473
|
|
btm_disassoc_timer_threshold=10000
|
|
minimum_btm_candidate_score=0
|
|
roam_candidate_validity_timer=0
|
|
|
|
#Timer waiting for interface up from the upper layer
|
|
gInterfaceChangeWait=2000
|
|
|
|
# Set external ACS Policy to Mandatory
|
|
acs_policy=1
|
|
|
|
# Set Modulated Dtim
|
|
gEnableModulatedDTIM=2
|
|
|
|
# Enable NAN datapath
|
|
genable_nan_datapath=1
|
|
|
|
# Set MaxLIModulate Dtim
|
|
gMaxLIModulatedDTIM=6
|
|
|
|
# Used for ignore peer infrormation
|
|
gIgnorePeerErpInfo=1
|
|
|
|
# DBS Scan Selection
|
|
gdbs_scan_selection=5,4,1,16,4,1
|
|
|
|
# 0 - Disallow STA+SAP SCC on LTE coex channel
|
|
# 1 - Allow STA+SAP SCC on LTE coex channel
|
|
g_sta_sap_scc_on_lte_coex_chan=1
|
|
|
|
# Tx Chain Mask for CCK
|
|
gCckChainMaskEnable=1
|
|
|
|
# Tx Chain Mask for 1SS
|
|
gTxChainMask1ss=0
|
|
|
|
# TPC power
|
|
gSelfGenFrmPwr=3
|
|
|
|
# Enable LFR3 subnet detection
|
|
gLFRSubnetDetectionEnable=0
|
|
|
|
#Enable APF in Active mode
|
|
gActiveUcBpfMode=2
|
|
|
|
# Control MC/BC active APF mode
|
|
gActiveMcBcBpfMode=1
|
|
|
|
# Enable or disable Probe Req Information Element whitelist. When enabled, IEs corresponding to bits
|
|
# set in bitmaps are allowed in probe request, all others removed while device is unassociated
|
|
# with an AP
|
|
# 1=Enable, 0=Disable (default)
|
|
g_enable_probereq_whitelist_ies=1
|
|
|
|
# ie bitmap examples: <bitmap_name>=<value> [<Allowed Information elements>]
|
|
# g_probe_req_ie_bitmap_0=0x80000009 #[0, 3, 31]
|
|
# g_probe_req_ie_bitmap_0=0x00000000 #[] (default)
|
|
# g_probe_req_ie_bitmap_1=0x80000009 #[32, 35, 63]
|
|
g_probe_req_ie_bitmap_0=0x0000000B
|
|
g_probe_req_ie_bitmap_1=0x00040000
|
|
# g_probe_req_ie_bitmap_2=0x00000000
|
|
# g_probe_req_ie_bitmap_3=0x00000000
|
|
# g_probe_req_ie_bitmap_4=0x00000000
|
|
# g_probe_req_ie_bitmap_5=0x00000000
|
|
g_probe_req_ie_bitmap_6=0x20000000
|
|
# g_probe_req_ie_bitmap_7=0x00000000
|
|
|
|
# Used to specify vendor specific OUIs
|
|
gProbeReqOUIs=0050F208
|
|
|
|
# enable 11d in world mode
|
|
enable_11d_in_world_mode=1
|
|
|
|
# WLM flags setting for low level
|
|
wlm_latency_flags_low=0xc08
|
|
|
|
#Enable/Disable chain selection optimization for one chain dtim
|
|
#Min: 0
|
|
#MAX: 30
|
|
gEnableDTIMSelectionDiversity=3
|
|
|
|
# Enable/Disable rtt sta mac randomization
|
|
enable_rtt_mac_randomization=1
|
|
|
|
# Set max time for active 2G channel scan
|
|
active_max_channel_time_2g=40
|
|
|
|
# To config roaming scan policy
|
|
roaming_scan_policy=1
|
|
|
|
# Config DPTRACE
|
|
gDptraceConfig=1,6,2,126
|
|
|
|
# Enable/Disable peer unmap confirmation support in Host
|
|
gEnablePeerUnmapConfSupport=1
|
|
|
|
# Enable/Disable separate wifi aware interface
|
|
nan_separate_iface_support=1
|
|
|
|
# Config Thermal mitigation
|
|
gThrottleDutyCycleLevel0=0
|
|
gThrottleDutyCycleLevel1=0
|
|
gThrottleDutyCycleLevel2=10
|
|
gThrottleDutyCycleLevel3=30
|
|
gThrottleDutyCycleLevel4=50
|
|
gThrottleDutyCycleLevel5=70
|
|
|
|
# Enable/Disable conversion from SARV1 to SARV2
|
|
gEnableSARV1toSARV2=1
|
|
|
|
#This ini is used to enable/disable ESE feature
|
|
EseEnabled=1
|
|
|
|
# Configure max number of ndi host supports
|
|
ndi_max_support=2
|
|
|
|
# Use wake lock during user scan
|
|
wake_lock_in_user_scan=1
|
|
|
|
# To address an interop issue with a particular AP
|
|
# Used to specify action OUIs to reconnect when assoc timeout
|
|
gActionOUIReconnAssocTimeout=00E04C 00 01
|
|
|
|
# Limit to send request to the firmware at most once in a second
|
|
nb_commands_interval=1
|
|
|
|
END
|
|
|
|
# Note: Configuration parser would not read anything past the END marker
|
|
|